Shorelandr CL2022 Manual do Utilizador descarregar pdf

CL2022 & CL2022 B

CL2022 Center Lift Pontoon

2 4300182 20.5 X 8 X 10-E Tire/MSilver Rim (or)

2 4300204 20.5 X 8 X 10-E Tire/Galv Rim

1 62340 Literature Bag - Trailers

1 65846-- Frame Bundle - 20 Single Axle CL

1 3110267 Winch DLB2000 Brake W/7 Handle

Tire Size & Carrying

Capacity Chart

Tire Load Carrying

Size Range Capacity

20.5 X 8 X 10 E 1535 lb. per/tire

Refer to tire side wall for proper tire pressure.

Tongue Weight Adjustment

Approximate Tongue Weight for Best Towing.

Tongue weight too high, move the axle assembly forward.

Tongue weight too low, move the axle assembly backward.

Tongue weight should be 5% to 7% of the total gross

weight of the boat and trailer combined.

Final Assembly Instructions

CL2022 B Center Lift Pontoon W/Brakes

2 4300182 20.5 X 8 X 10-E Tire/MSilver Rim (or)

2 4300204 20.5 X 8 X 10-E Tire/Galv Rim

1 62340 Literature Bag - Trailers

1 66041-- Frame Bundle - 20 Single Axle W/Brakes

1 3110267 Winch DLB2000 Brake W/7 Handle

1 65789 Brake Kit 20-24 CL One Axle W/Brakes

Remove the items from the main frame by cutting the

banding. Remove the hardware bag and sort the parts by

size.

Torsion Axle:

Mount the axle assembly (Ref.#86) to the center lift frame

(Ref.#30) using four (4) 1/2 X 4 hex bolts, four (4) 1/2 flat

washers and with 1/2 flange lock nuts. Refer to the parts

drawing for the proper placement of the hardware.

Mount the tire and rim assemblies using 80-90 ft. lbs.

torque on the lug nuts using a proper tightening procedure.

Tongue:

Mount the tongue weldment (Ref.#73) to the center lift

frame (Ref.#30) using two (2) 1/2 X 4-1/2 hex bolts and

secure with 1/2 flange lock nuts. After mounting the

tongue to the frame weldment, secure the ground wire with

a 1/4 X 3/4 grounding screw (Ref.#84) to the inside of the

frame as shown in the drawing.

Wiring:

Your new pontoon trailer comes pre-wired. Once the

tongue is installed, plug the yellow wired plug of the

tongue harness. Likewise the green wired plugs are

connected to each other. This is necessary to have your

lighting function properly.

Safety Chains:

Install the safety chains to the tongue by placing a flat

washer at head of the 3/8 X 1-1/4 hex bolt. Insert the bolt

into the end link of the chain and place in the hole provided

in the tongue for the safety chains. Secure with a 3/8 flat

washer and 3/8 flange lock nuts on the inside of the

tongue. Tighten. Repeat on the other side of the tongue.

Front Boat Stops:

Place the front stop weldment (Ref.#49) in the desired

position to stop your boat as it is being loaded on the

trailer. Secure it to the frame with a 1/2 square u-bolt

(Ref.#83) and a 1/2 lock washer (Ref.#59) and 1/2 hex

nut (Ref.#46). Repeat on the other stop. (Note that the

stops are to be used as a stop to which your boat is

winched into position for towing as well as a stop when

driving your pontoon on the trailer.)

Load Guides:

Measure the distance between the pontoons. Allow 1/2

clearance on each side between the pontoon tube and the

load guide you are about to install. Slide out to the correct

width determined at the beginning of this installation. Note

that there are several holes in the bracket to accommodate

various widths of adjustment. Select the one that best

matches your determined width. Secure with a 3/8 flange

lock nuts. Do not tighten at this time. Repeat this process

on the load guide directly across the frame. Double check

the measurement to make sure that you have the correct

clearance between the load guide and the pontoon tube.

Place in the 3/8 X 1 and 3/8 X 4 hex bolts and 3/8

flange lock nuts to secure the load guide as well. Tighten

bolts just installed.

For Brake Models Only:

Actuator & Safety Chain:

Slide the actuator into the actuator housing unit and secure

1 2 3 4

Resumo do Conteúdo

Página 1

®CL2022 & CL2022 BCL2022 Center Lift Pontoon2 4300182 20.5 X 8 X 10-E Tire/MSilver Rim (or)2 4300204 20.5 X 8 X 10-E Tire/Galv Rim1 62340 Literatu

Página 2 - Material List for the CL2022

Material List for the CL2022NOTE: ShoreLandr offers their product line in either galvanized or painted finish. When ordering parts it is important th

Página 3 - Parts Drawing

Parts DrawingNOTE: Optional equipmentand replacement parts must bepurchased through an autho-rized ShoreLandr dealer.CL2022 is shown in parts drawing

Página 4 - Rear Axle

with two (2) pins and snap rings provided with the actuator.Secure the actuator-housing unit to the front of the tongueusing the three (3) 1/2 X 4 h

Modelos relacionados CL2022B

Comentários a estes Manuais

Sem comentários

Shorelandr CL2022 Manual do Utilizador

Consulte online ou descarregue Manual do Utilizador para Reboques Shorelandr CL2022. ShoreLand'r CL2022 User Manual Manual do Utilizador

Resumo do Conteúdo

Modelos relacionados CL2022B

Comentários a estes Manuais

Manuais e produtos relacionados com Reboques Shorelandr CL2022